AMPELITE – Commercial Roofing – Wonderglas S-996
Wonderglas S-996 – Industrial Fibreglass Roofing & Skylights
Ampelite introduced Wonderglas S-996 gel-coated sheeting to New Zealand in 1995 expressly to combat our very harsh environment. Its highly UV-resistant gel coat provides Wonderglas S-996 with the ultimate impenetrable barrier, reducing surface erosion and loss of light transmission to negligible proportions. The proven performance of Wonderglas S-996 remains unsurpassed and continues to be a preferred solution for commercial buildings throughout the country. It is recommended for commercial and retail applications where excellent long-term light transmission is required.
Wonderglas S996 is backed by the best in market warranty of 25 years for both water transmission and light transmission and is manufactured in strict accordance with the New Zealand standard AS/NZS 4256, Parts 1 & 3: 1994.6, Standards License No.SMKB20116.
Wonderglas S996 is manufactured using Ampelite’s Proprietary SL Group 3 ‘Bromine Free’ Fire Retardant Resin System. Surface Finish Properties have been tested to ISO 5660 and achieved a group number 3 performance in accordance with NZBC Verification Method C/VM2 Appendix.
MAIN BENEFITS
- Available in 1.1mm / 1800gsm, 1.4mm / 2400gsm, 1.7mm / 3050gsm, 2.2mm / 3660gsm, 2.5mm /
4270gsm and 2.8mm / 4880gsm - Best in market warranty – 25 years
- Excellent light transmission
- Superior resistance to yellowing and hazing
- Minimum loss of light transmission over life
- 99% protection from UV light
- Full proprietary fixing system and accessories available
- Surface Finish Properties – group number 3
WONDERGLAS S-996 – Sheeting Information
PLANNING
Available Colours; Light and Heat Transmission
Wonderglas S-996 is available in Clear, Opal and Grey. For information on other colours, please contact your local Ampelite office.
LIGHT & HEAT TRANSMISSION 1.1 MM
| COLOUR | LIGHT (%) | HEAT (%) |
|---|---|---|
| Clear | 80 | 78 |
| Grey | 33 | 58 |
| Opal | 60 | 58 |
For light and heat transmission of Series 2400, 3050, 3660, 4270, 4880, please contact your local Ampelite office.
Available Profiles & Spanning Capacity
All current profiles such as Corrugated, 5 rib, LT7, BB900, etc. plus most superseded profiles are available.
Please download our list of popular profiles.
PROFILES & SPANNING CAPACITY (BETWEEN PURLINS)
| SPANNING | 1.5KPA | DRAPE CURVE RADIUS | ||||
|---|---|---|---|---|---|---|
| Gauge | 1.1mm / 1800 | 1.4mm / 2400 | 1.7mm / 3050 | 2.2mm / 3660 | 1.1mm / 1800 | 1.4mm / 2400 |
| Corrugated | 1000 | 1200 | 1300 | 1400 | 4m | 5m |
| SixRib | 1000 | 1200 | 1300 | 1400 | 5m | 6m |
| 5 Rib | 1200 | 1500 | 1700 | 1900 | 8m | 9m |
| Trimline | 1200 | 1500 | 1700 | 1900 | 8m | 9m |
| MC700 MC750 MC770 | 1200 | 1500 | 1700 | 1900 | 8m | 9m |
| Metric Windek MC1000 | 1200 | 1500 | 1700 | 1900 | 8m | 9m |
| Ribline 960 | 1200 | 1500 | 1700 | 1900 | 12m | 14m |
| Steelspan Topspan | 1600 | 1800 | 2100 | 2400 | 16m | 18m |
| Multispan MC930 Maxispan | 1600 | 1800 | 2000 | 2300 | 16m | 18m |
| LT7 ST7 Silbery | 1400 | 1700 | 1900 | 2200 | 12m | 14m |
| BB900 ST900 Multirib | 1400 | 1700 | 1900 | 2200 | 12m | 14m |
| DD300 DD400 | 1200 | 1400 | 1700 | 2000 | 16m | 18m |
| Kliplok 406 | 1200 | 1500 | 1700 | 1900 | 16m | 18m |
| Supersix | 1600 | 1800 | 2100 | 2400 | 16m | 18m |
AMPELITE – WONDERGLAS S-996
INSTALLATION
Correct Installation is Important
Ampelite sheeting shall be installed in accordance with Ampelite fixing instructions and with AS/NZS 1562.3:1996, Design and installation of sheet roof and wall cladding, Part 3: Plastic, the requirements of the NZ building code and the NZ Metal Roofing Manufacturers’ Association Code of Practice. For full installation details, please download a copy of our installation guide.
Please note these additional important requirementst
- Ampelite translucent sheeting matching positive fixed profiles shall be installed using the fastening length applicable to the main cladding, together with a metal profile washer and EDPM seal. This combination creates a secure and weather-tight finish. The fixing screws should not be over-tightened to the extent that the sheet buckles, allowing water penetration at the seal or sheet overlap.
- Fixing should be made at every crest at both ends of the sheet and at every second crest at intermediate purlins.
- Where Ampelite fibreglass sheeting is in contact with safety mesh, an Ampelite purlin protection strip must be installed over the safety mesh to avoid fracturing of the underside of the sheet.
- Where end-lapping of the sheet is required, a minimum of 300 mm overlap is essential. Ampelite recommends the use of 25 mm Lap Seal Tape at the top and bottom edges of the purlin. This ensures the strips are concealed. For Decking profiles, two continuous beads of a clear non-hardening sealer (i.e. silicone), must be applied across the full width of the decking within the overlap.
- IMPORTANT: Ampelite sheeting should be installed by pre-drilling oversize holes to allow for expansion and contraction. The basic calculation is 0.75 mm per lin. /m, plus shank diameter of screw. Do not over-tighten screws. EXAMPLE: 10 m sheet – 10 (m) x 0.75 (mm) + 4 mm (fastener) = 11.5 mm pre-drilled hole.
- CLIP-FIXED DECKING: Ampelite sheeting matching clip-fixed deck profiles shall be installed in conjunction with the main cladding and should be side lapped with overlaps on both sides (Ampelite sheets have two female laps). Fixing of sheets should be carried out in the same manner and practice as those stated for positive fixed profile roofing.
- WALL CLADDING: Pan fixing is required at each girt, and the use of Ampelite grey dome 22 mm weather seals ensures a weather-tight seal. Over-tightening or flattening the weather seal must be avoided. Fixing shall occur in every pan at both ends of the sheeting, and at every other pan at intermediate girts.
- CYCLONE ZONE INSTALLATION: Installation in cyclone-prone areas follows the recommendations and code for normal fixing, but further specific requirements must be met. Please contact your local Ampelite office for the latest information.
Industrial Profile Brochure
Ampelok Fasteners Brochure
Accessories & Fixings
Cleaning and Maintenance
Accessories
Ampelite has a large range of accessories available to help make the installation of Wonderglas S-996 fast and professional. These accessories include a range of self-drilling screws which oversize the fastener holes as they pass through the sheet, and self-adhesive tapes and profiled form filler strips for vermin protection.
Handling, Storage, & Disposal
WonderGlas S-996 industrial fibreglass sheeting is a non-trafficable roofing material. It should always be stored in a dry and fire-safe area and handled with care to avoid damage to the surface coating. Warranties will not apply to sheeting that has been damaged in handling or has mechanical damage as a result of foot traffic.
Fibreglass sheeting is not recyclable and should be disposed of in a landfill. Do not incinerate fibreglass off-cuts as burning produces acrid smoke and noxious, toxic fumes.
Safety Data
Eye Contact: Can cause irritation. Appropriate eye protection should be worn. If irritation occurs due to exposure to dust particles, wash eyes with running water using an eye bath or wash bottle. If irritation persists, seek medical attention.
Skin Contact: Can cause irritation. Shower thoroughly using soap and a cloth or sponge.
Inhalation: Dust masks are recommended, although particles are not respirable.
Ingestion: Non-toxic. Extensive studies have revealed no serious effects.
